sunjiakang66@outlook.com         +86 155 1660 9511
Is the Damage in the Bore, the Face, or the Shaft End? Routing Xinda XDT / XDFC / XDZ Without Wrong Turns
Home » News » Is the Damage in the Bore, the Face, or the Shaft End? Routing Xinda XDT / XDFC / XDZ Without Wrong Turns

Products Catalog

Contact  us

Is the Damage in the Bore, the Face, or the Shaft End? Routing Xinda XDT / XDFC / XDZ Without Wrong Turns

Views: 0     Author: Site Editor     Publish Time: 2026-11-09      Origin: Site

The step that trips people up in portable machine-tool buying isn't "which model" — it's "which series first." When a maintenance crew gets a work order, the reflex is "find a portable lathe." But "the hole is worn," "the flange leaks," and "the shaft end is sweating oil" are three different failure geometries, mapping to three non-interchangeable product lines. Pick the wrong series and even the right model is useless.

Xinda's portable machine family is not organized by size — it's organized by what geometric feature on the workpiece is damaged:

  • Bore damaged​ → XDT boring machine​ (through-bar re-rounding; wall loss can be rebuilt with same-bar welding)

  • Face damaged​ → XDFC flange lathe​ (mounts on the flange, turns face / seal face / grooves)

  • Shaft-end OD damaged​ → XDZ shaft-end lathe​ (fixed-disk locks the shaft system, no shaft removal)

  • Plane / guide rail / mounting seat damaged​ → portable milling machine​ (single-arm mill / gantry mill — not mixed into the three lines above)

I. Routing by failure geometry: how to read three work orders

Work order A:​ "Excavator bucket-lug hole went oval, pin wanders."

Damaged feature = inner bore → XDT line

φ90–160 mm, single hole, possible wall loss → XDT50 bore-weld all-in-one​ (220 V, same-bar welding) or XDT60​ (if 380 V available, denser workload)

Do not dispatch XDFC (it doesn't bore) or XDZ (a shaft end is not an articulated hole).

Work order B:​ "Pump discharge flange leaks, deep old-gasket imprint, serration worn off-center."

Damaged feature = flange face → XDFC line

First ask: is the bore through?

  • Bore intact → small-bore XDFC250 internal support​ / large-bore XDFC1000 internal support

  • Bore blocked / blind flange / valve seat → XDFC300 external clamp

Do not dispatch XDT (bores the hole but doesn't true the face) or XDZ (shaft end is not a flange face).

Work order C:​ "Water-pump shaft seal section has a groove scored in, oil weeping."

Damaged feature = shaft-end OD → XDZ line

Shaft end has a mounting face → XDZ300 fixed-disk version​ (220 V, quick mount)

Smooth shaft / no drilling allowed → XDZ300 external-clamp version

Do not dispatch XDFC (doesn't do flange faces) or XDT (bores holes, doesn't turn shaft OD).

II. Overlap and crossover: when to use "combined configuration"

Real jobs aren't always clean — three damage types stack:

Flange + bore both damaged (e.g., valve body)

  • Flange face → XDFC trues the face

  • Valve-seat bore → XDT through-bar boring (where space allows)

Sequence: bore first to set the datum, then face the flange; or two separate setups per workpiece geometry. Don't expect one machine to do both in one clamp.

Shaft end + adjacent flange face both damaged (e.g., gearbox output shaft)

  • Shaft OD / seal section → XDZ fixed disk

  • If the flange connection face is also worn → swap to a face tool under the same datum (confirm the sub-type includes it), or re-clamp with XDFC for a second operation

Don't force XDZ to face a large flange — its swing envelope and tool-arm travel were not designed for big flange faces.

Mounting-seat plane + threaded-hole pattern (e.g., pump base, motor shim)

Belongs to portable milling (XDDBX single-arm mill / XDLMX gantry mill), not XDT / XDFC / XDZ.

Rule: if the damage is a "plane / framed face" rather than a "rotational feature (hole / face / shaft)" → route directly to the milling line.

III. The four-screen selection filter (earlier than "which model")

Running these four screens before ordering blocks ~90% of wrong purchases:

① What's damaged — bore, face, shaft end, or plane?

→ First fix the series: XDT / XDFC / XDZ / milling. Don't compare specs across lines.

② Where is the clamping datum?

Is the bore through? Is the flange bore intact? Does the shaft end have a disk face?

→ Determines internal support / external clamp / fixed disk / external shaft collar.

③ Which size segment?

  • XDT: φ45 → φ1000+ by bar-diameter segments

  • XDFC: DN15 → φ2000 by internal-support / external-clamp segments

  • XDZ: φ50 → φ500 by whether the shaft end can be locked to a disk

④ What are the site constraints?

220 V / 380 V / no power / hydraulic?

Can you do hot-work welding for supports? Are neighboring pipes dense? Any cleanroom / explosion-proof requirement?

Can it fit through manholes / pipe tunnels / tower sections?

⚠️ Don't select backwards: asking "do we have 380 V" before fixing the series tends to push a hand-crank, no-power cleanroom small flange toward a big electric machine.

IV. One-line takeaway

Portable machine selection's first question is not "which model" — it's "is the damage in the bore, the face, or the shaft end."

Bore → XDT, face → XDFC, shaft end → XDZ, plane → milling.

The series decides right-or-wrong; the model decides coarse-or-fine; the working condition decides the sub-type.

Reverse the order and you get the classic rework story: "bought the right model, dispatched the wrong series, can't do the job on site."

(This article is compiled from publicly available corporate materials and industry information for reference only. Specific product information and service terms are subject to the official release of the manufacturer.)

We use cookies to enable all functionalities for best performance during your visit and to improve our services by giving us some insight into how the website is being used. Continued use of our website without having changed your browser settings confirms your acceptance of these cookies. For details please see our privacy policy.
 
TEL: +86 183 3735 8388
×